80190-219-01D擴展驅動模塊庫存

類目：A-B
型號：80190-219-01D
全國服務熱線：+86 15270269218
手機：+86 15270269218
微信：+86 15270269218
QQ：3136378118
Email：stodcdcs@gmail.com

在線咨詢

產品詳情

產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等。
主營DCS控制系統備件，PLC系統備件及機器人系統備件，
優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
80190-219-01D擴展驅動模塊庫存

發電機單獨運行：當發電機不并聯運行時如果不需要無功電壓降，則使用以下方法之一消除并聯變壓器影響的方法在電壓調節器內。
-在電流互感器上安裝一個單元/并聯開關在單臺發電機運行期間關閉開關。
-將電壓下降電阻器R4設置為其小下降位置。
-在發電機單獨運行的情況下，安裝跨接線端子CT和CT1。
UFL電路50/60和400 Hz選擇器J1：低頻限值部件或V/Hz部件位于電壓調節器上
電路板（見圖9）。組成UFL或V/Hz的部件部件如圖11所示。跨接導線J1消除了
電阻器R57的影響。拆下跨接線J1將R57置于電路中。
60或400 Hz操作：確保跨接導線安裝在標記為J1的區域。導線安裝在電路板的組件側，并且
跨接導線的端部焊接在電路板的箔側。
50Hz操作：確?？缃訉?dǎo)線已從跨接導線上拆下標記J1的區域。通過切斷跨接導線的兩端拆下J1。
電壓調節器保險絲：電壓調節器包含15 a正常值熔斷電壓調節器輸入電源電路中的保險絲（見圖1、2和3）。在電壓調節器功率要求為：減少，如與小型發電機一起使用時，勵磁小于因此，可以使用較小的保險絲。切勿安裝大于15 a的保險絲切勿安裝延遲型保險絲。
附件項目：發電機系統提供的附件項目
必須按照隨附的接線圖所示進行連接發電機組和附件項目圖紙或說明?？吹竭B接時應遵循的注意事項和一般程序配件。
電壓停機（發動機怠速開關）：系統可配備在緊急情況下或當原動機必須以降低的速度運行。此開關必須為放置在調節器的輸入電源線上（端子P1或P2）。現場斷路器? eld斷路器必須為以下類型：具有用于熱元件和觸點的單獨端子。
斷路器熱元件從? 埃爾德電流或發電機線路電流。在那里它被加熱? eld電流熱元件連接在電壓調節器輸出和勵磁機之間? 埃爾德。在由發電機線路電流加熱的情況下元件連接到位于其中一個發電機中的電流互感器載重線。
自動/手動電壓控制：自動/手動壓力控制選項包括下面描述的組件。連接自動/手動電壓控制模塊，如提供的接線圖所示發電機。
-三位選擇開關：當該開關設置為自動時，通過開關觸點向調節器輸入電源供電端子P1和P2。當開關設置為MAN時，供電通過開關觸點連接至手動電壓控制電路直腸? 呃。OFF（斷開）位置打開兩個電壓的輸入電源調節器和手動電壓控制電路? 呃。
-手動電壓控制電路：手動電壓控制回路由全波直肌組成? er組件和手動電壓控制變量。手動電壓控制變量控制發電機發電機組在手動電壓下運行時輸出控制操作模式。Generator operating singly: When generators are not operating parallel
and reactive voltage droop is not required, use one of the following
methods to eliminate the effect of the parallel operation transformer
within the voltage regulator.
- Install a unit/parallel switch across the current transformer
secondary, and close switch during single generator operation.
- Set the voltage droop resistor R4 to its minimum droop position.
- Where the generator will be operating singly, install a jumper across
terminals CT? and CT1.
UFL circuit 50/60 and 400 Hz selector J1: The underfrequency limit
components or V/Hz components are located on the voltage regulator
circuit board (see Figure 9). Parts comprising the UFL or V/Hz
components are shown in Figure 11. A jumper wire J1 eliminates the
effect of resistor R57. Removing the jumper J1 places R57 in the circuit.
60 or 400 Hz operation: Make certain the jumper wire is installed across
area marked J1. Wire is mounted on component side of circuit board and
ends of jumper wire are soldered on foil side of the circuit board.
50 Hz operation: Make certain the jumper wire is removed from across
area marked J1. Remove J1 by cutting each end of the jumper wire.
Voltage regulator fuse: The voltage regulator contains a 15 A normal
blow fuse in the voltage regulator input power circuit (see Fig. 1, 2
and 3). In applications where voltage regulator power requirements are
reduced, as when used with small generators where excitation is less than
given, a smaller fuse may be used. Never install a fuse larger than 15 A
and never install a delay-type fuse.
Accessory items: Accessory items provided with the generator system
must be connected as shown on the wiring diagram provided with the
generator set and the accessory item drawing or instruction. Observe
the precautions and general procedures that follow when connecting
accessory items.
Voltage shutdown (engine idle switch): The system can be equipped with
a switch to allow removal of excitation in an emergency or when the
prime mover must be operated at reduced speeds. This switch must be
placed in the input power line to the regulator (terminal P1 or P2).
Field circuit breaker: The ? eld circuit breaker must be of the type that
has separate terminals for the thermal element and the contacts.
The circuit breaker thermal element receives heat from either the ? eld
current or generator line current. Where it is heated by ? eld current, the
thermal element connects between the voltage regulator output and the exciter ? eld. Where it is heated by generator line current, the thermal
element connects to a current transformer located in one of the generator
load lines.
Auto/manual voltage control: The auto/manual voltage control option
includes the components described below. Connect the auto/manual
voltage control module as shown on the wiring diagram provided with
the generator.
- Three-position selector switch: When this switch is set to the AUTO,
power is fed across the switch contacts to the regulator input power
terminal P1 and P2. When the switch is set to MAN, power is fed
across the switch contacts to the manual voltage control circuit
recti? ers. OFF position opens input power to both the voltage
regulator and the manual voltage control recti? ers.
- Manual voltage control circuit: The manual voltage control circuit
consists of a full wave recti? er assembly and a manual voltage
control variac. The manual voltage control variac controls generator
output whenever the generator set is operated in the manual voltage
control mode of operation.

相關產品